Select a Country
  • {{country.Text}}
Select a Language

Features

  • 1 HP Heavy-Duty Motor - heavy duty induction motor operates on 120 V or 240 V, totally enclosed to prevent sawdust contamination, fan cooled for longer life, belt drive delivers smooth consistent power
  • Heavy duty, easy-to-assemble construction - rugged cast iron bed minimizes vibration, machine ground surfaces for precise jointing/planing, sturdy heavy gauge wide stance cabinet with built-in sawdust collection port and on-board tool storage
  • Dual Bevel Fence - with stops at 45°, 90° and 135°
  • Convenient Dust Port - quickly slides out of the way when not in use, provides on-board storage for blade alignment tools
  • Versatile Bed/Table - long 45 in. bed gives greater support to large workpieces, rabbeting ledge for precise rabbets up to 1/2 in. deep, adjustable front and rear tables

Specifications

Input 1 HP TEFC induction, 12/6 Amps., 120 V / 240 V
Cuts per Minute 15,000
Knives three HSS
Knife Adjustment jack screw(s)
Bed Length 45 in.
Max. Planing Width 6-1/8 in.
Max. Depth-of-Cut/Pass 1/8 in.
Rabbet Capacity 1/2 in.
Tool Weight 213 lb.

Ordering Information

{{model}}
Catalog Number Model No. Description
14668 JP0610  6 1/8 Inch Jointer/Planer 
Includes

Cabinet, 2 push blocks, angle gauge, dust chute, fence assembly, cutter guard and adjustment wrenches
6 1/8" Jointer/Planer is rated 4.7 out of 5 by 3.
  • y_2016, m_12, d_5, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en, sid_797, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=AGE, direction=DESCENDING)]
  • clientName_ridgid
  • bvseo_sdk, net_sdk, 3.2.0.0
  • CLOUD, getAggregateRating, 99ms
  • REVIEWS, PRODUCT
Rated 4 out of 5 by from This a reliable smooth cutting machine. Make sure you have adequate chip extraction with a high volume dust collector or be ready to stop often and remove chips. This is not the fault of the machine. It's doing what it was designed to do and does it well. It will leave you with a surface ready for finishing if you don't rush your work. I didn't give it a 5 star since the rabetting function comes up short when making multiple pass rabbets.
Date published: 2016-07-27
Rated 5 out of 5 by from Great tool, works perfectly. Very easy to setup and install, took very little configuration and is also easy to maintain. Solid extended fence is great for long pieces, jointed over 1000 peices of wood and is still working great.
Date published: 2014-11-25
Rated 5 out of 5 by from Great Jointer, exceeds expectations for the Value Got this jointer from my local Home Depot with a discount by using my HD card. This made it an even better value. Set-up was easily accomplished follow Ridgid’s instructions. I had a job waiting to use that weekend. Tool made clean cuts, square and true. Dust collection was excellent. I highly recommend this tool.
Date published: 2014-11-24
  • y_2016, m_12, d_5, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en, sid_797, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=AGE, direction=DESCENDING)]
  • clientName_ridgid
  • bvseo_sdk, net_sdk, 3.2.0.0
  • CLOUD, getReviews, 3ms
  • REVIEWS, PRODUCT
5 Questions | 8 Answers

Product Q&A

 
 
Back >>
 
 
2 years, 11 months ago
Customer avatar
by
Ben Wheeler, TX 75754, USA
Read all my Q&A
 
Please wait while more information about Paul7 is loaded.
Additional information about Paul7 could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Please contact your local Home Depot store for information on how to order blades and what is available.
2 years, 11 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGIDSupport is loaded.
Additional information about RIDGIDSupport could not be loaded.
0points
2out of 4found this answer helpful.
Was this helpful?helpful2unhelpful2

Answer: 
Please contact your local Home Depot to purchase blades. All RIDGID wood working power tool retail distribution is handled through Home Depot in the U.S. and Canada.
2 years, 11 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGIDSupport is loaded.
Additional information about RIDGIDSupport could not be loaded.
-3points
2out of 7found this answer helpful.
Was this helpful?helpful2unhelpful5
I want to hook up a dust collector. I would assume it's a 4" port, but want to confirm.
2 years, 3 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about j55b is loaded.
Additional information about j55b could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Thank you for your interest in RIDGID!

Yes, the JP0610 jointer/planer has a 4” dust collection chute.

Regards,
RIDGID
2 years, 2 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGIDtools is loaded.
Additional information about RIDGIDtools could not be loaded.
0points
1out of 2found this answer helpful.
Was this helpful?helpful1unhelpful1

Answer: 
Yes, 4" port.
2 years ago
Customer avatar
by
Arizona, United States
Read all my Q&A
 
Please wait while more information about BigP is loaded.
Additional information about BigP could not be loaded.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
The manual describes creating wide rabbets but doesn't work as described unless you are making only one pass. Since I'm working in maple it needs to be shallow cuts. The project requires a 3/16" rabbet.

The infeed table is 3/4 plus inches wider on the outer edge causing a misalignment between it and the outfeed tables outer edge. When creating rabbets in incremental passes as directed in the instructions in the manual the infeed table being wider causes the board to enter the knives at an angle creating a tapered cut since the outer edge of the board is higher than the inside edge against the fence. This is not good and can't possibly work as described.

Do you have any suggestions.

I tried following the instructions and on a 3 3/4" inch wide rabbet. It yields a cut that is about 1/32 inch narrower on the edge nearest the fence when taking 1/16" cuts in two passes.
4 months, 1 week ago
Customer avatar
by
Roswell, GA, USA
Read all my Q&A
 
Please wait while more information about itsme is loaded.
Additional information about itsme could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Thank you for contacting RIDGID. The JP0610 jointer-planers in-feed table is designed to be wider than the out-feed table, in support of the wood stock up to the point of where it contacts the spinning blades. The blades remove the material in a rabbeting cut, and then the wood slides onto the out-feed table where support for the stock is continued, until the entire length of the cut is completed. If the wood stock is contacting the blades at an angle, that would be due to either the fence not being square to the tables, the wood stock not being securely held in place on the in-feed table and against the fence, or the in-feed table having some type of alignment issue with the cutter head. The width of the in-feed table only service to supports the wood stock.

To have an in-depth conversation concerning the RIDGID JP0610 jointer-planer can be conducted by contacting the RIDGID Technical Service and Customer Service staff at 1-866-539-1710.
4 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGID14 is loaded.
Additional information about RIDGID14 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Answer: 
The JP0610 jointer-planers in-feed table is designed to be wider than the out-feed table, in support of the wood stock up to the point of where it contacts the spinning blades. The blades remove the material in a rabbeting cut, and then the wood slides onto the out-feed table where support for the stock is continued, until the entire length of the cut is completed. If the wood stock is contacting the blades at an angle, that would be due to either the fence not being square to the tables, the wood stock not being securely held in place on the in-feed table and against the fence, or the in-feed table having some type of alignment issue with the cutter head. The width of the in-feed table only service to supports the wood stock.

For an in-depth conversation concerning the RIDGID JP0610 jointer-planer please contact RIDGID Technical Service and Customer Service staff at 1-866-539-1710.
4 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGID14 is loaded.
Additional information about RIDGID14 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
3 years ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about TeslaFreshPower is loaded.
Additional information about TeslaFreshPower could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
RIDGID, as a manufacturer, does not offer any form of direct wood working power tool sales. All RIDGID wood working power tool retail distribution is handled through Home Depot in the U.S. and Canada. You will need to contact your local store for information on stock.
3 years ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGIDSupport is loaded.
Additional information about RIDGIDSupport could not be loaded.
0points
2out of 4found this answer helpful.
Was this helpful?helpful2unhelpful2
 
1 answer

dust vac chute

Do you make a reducer to attach a ridged 16 gallon shop vac
1 year, 10 months ago
Customer avatar
by
Walden, NY, USA
Read all my Q&A
 
Please wait while more information about Kitman is loaded.
Additional information about Kitman could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Thank you for contacting RIDGID.

We have an adapter kit (VT1755 part number) that contains the reducer. One is from 2 ½” down to 1 7/8” and the other adapter is from 1 7/8” down to 1 ¼”. These are the only reducer adapters we have and you must check the size of the dust port of your planer to see if either of these will fit. This kit is available at Home Depot stores.

Regards,
RIDGID
1 year, 10 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RIDGIDtools is loaded.
Additional information about RIDGIDtools could not be loaded.
-2points
0out of 2found this answer helpful.
Was this helpful?helpful0unhelpful2
1 of 1
  • 2016-12-06 T06:39:56.220-06:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_797, prod, sort_default
1 of 1
  • bvseo_sdk, net_sdk, 3.2.0.0
  • CLOUD, getContent, 30ms
  • QUESTIONS, PRODUCT