K-1500G Sectional Machine | RIDGID Professional Tools

Features

A gasoline engine makes the Model K-1500G well-suited for cleaning lines in remote locations where electrical power is unavailable. Cuts through roots fast.
Unique, easy-to-use, instant-acting cable clutch maximizes operator control. Pull down on the handle and the cable spins at 600 RPM. Release handle, cable stops instantly.
Comes equipped to use 1 1⁄4" (32 mm) cable to clean 3" (75 mm) to 10" (250 mm) lines through 300' (92 m).
6 HP gasoline engine drives cable via four-speed transmission. Allows the operator to vary the cable spinning speed to fit the application. Forward speeds of 333, 425 and 500 RPM, and a reverse speed of 250 RPM.
Low-profile, four-wheel cart easily rolls to the job. Guards against machine upset and possible fuel spillage.
Includes A-1 RIDGID® drain cleaning mitt and operator’s manual.

Specifications

Machine Dimensions

Width Wheel to Wheel	26" (66 cm).
Length Including Kickstand	28" (71 cm).
Ground to Top of Handle	38" (97 cm).
Back of Handle to Front	49" (124 cm).
Ground to Top of Housing Shell	27" (60 cm).

Support Documents

Parts List

K-1500G Parts List (453.86 KB)

Warranty

Full Lifetime Warranty

Ordering Information

Catalog Number	Model No.	Description	Weight
Catalog Number	Model No.	Description	lb.	kg
44587	K-1500G	Machine Only with A-1 RIDGID Drain Cleaning Mitt, A-12 Coupling Pin Key and A-34-10 Rear Guide Hose, A-369-X 1¼" (32 mm) Jaw Set	190	86.4
48462	K-1500G with C-14	Machine with Standard Equipment, includes: – Ten Sections Of C-14 Cable, Total 150' (45.7 m) – Three A-8 Cable Carriers – A-1 Left-Hand RIDGID Drain Cleaning Mitt – A-12 Coupling Pin Key – A-34-12 Rear Guide Hose – A-2864 Hex Key – A-3516 Hex Key – A-3 Tool Box – T-2 Heavy-Duty Straight Auger – T-4 Heavy-Duty Funnel Auger – T-6 Retrieving Auger – T-8 Grease Cutter – T-13 Sawtooth Cutter – T-50 Sharktooth Cutter	350	159.0

Tools

Catalog Number	Model No.	Description	Replac. Blade(s)
59480	T-11	“H” Cutter, 2 1⁄2" (65 mm)	97800
59485	T-12	“H” Cutter, 3 1⁄2" (89 mm)	97945
59625	T-21	Spiral Sawtooth Cutter, 2 1⁄2" (65 mm)	97970
59765	T-24	4-Blade Cutter, 21⁄2" (65 mm)	97940
59770	T-25	4-Blade Cutter, 3 1⁄2" (89 mm)	97975
59775	T-26	4-Blade Cutter, 4 1⁄2" (114 mm)	97805
59780	T-26A	4-Blade Cutter, 5 1⁄2" (140 mm)	97980
61770	T-15A	Expanding Cutter, 4" - 6" (110-150 mm)	62970
61790	T-4	Heavy-Duty Funnel Auger	-
61800	T-2	Heavy-Duty Straight Auger	-
61825	T-15B	Expanding Cutter, 6" - 8" (150-200 mm)	62980
61850	T-17	Spiral Bar Cutter, 6" (150 mm)	97955
61855	T-18	Spiral Bar Cutter, 8" (200 mm)	97960
61960	T-16	Spiral Bar Cutter, 4" (110 mm)	97855
61970	T-13	Sawtooth Cutter, 2 1⁄2" (65 mm)	98070
61975	T-14	Sawtooth Cutter, 3 1⁄2" (89 mm)	98075
62840	T-1	Straight Auger	-
62845	T-10	Grease Cutter, 4 1⁄2" (114 mm)	97865
63075	T-22	Spiral Sawtooth Cutter, 3" (75 mm)	97970
63085	T-23	Spiral Sawtooth Cutter, 4" (110 mm)	97850
63105	T-3	Funnel Auger	-
63110	T-31	Chain Knocker, For 3"- 4" Pipe (75-110 mm)	97985
63115	T-32	Chain Knocker, For 6" Pipe (150 mm)	97990
63120	T-33	Chain Knocker, For 8" Pipe (200 mm)	97995
63145	T-38	Flue Brush, 1 1⁄2" (40 mm)	-
63150	T-39	Flue Brush, 2" (50 mm)	-
63155	T-40	Flue Brush, 2 1⁄2" (65 mm)	-
63160	T-41	Flue Brush, 3" (76 mm)	-
63165	T-42	Flue Brush, 3 1⁄2" (89 mm)	-
63170	T-43	Flue Brush, 4" (110 mm)	-
63175	T-44	Flue Brush, 4 1⁄2" (114 mm)	-
63180	T-46	Flue Brush, 5 1⁄2" (140 mm)	-
63190	T-5	A-3565 Key	-
63195	T-6	Funnel Retrieving Auger Run Machine In Reverse	-
63200	T-7	Hook Auger	-
63205	T-8	Grease Cutter, 2 1⁄2" (65 mm)	97920
63210	T-9	Grease Cutter, 3 1⁄2" (89 mm)	97925
63240	T-45	Flue Brush, 5" (127 mm)	-
98030	T-50	Includes 3 Sizes: 3-4-5" (75-110-127 mm)	-
98035	T-50-1	Sharktooth Cutter, 3" (75 mm)	98005
98040	T-50-2	Sharktooth Cutter, 4" (110 mm)	98010
98045	T-50-3	Sharktooth Cutter, 5" (127 mm)	98015

Cables and Leaders

Catalog Number	Model No.	Description	Weight
Catalog Number	Model No.	Description	lb.	kg
25036	C-10 PC	7/8" (22 mm) x 15' Cable with Inner Core (4,6 m) Requires A-368-X Jawset	10	4.50
25046	C-11IC	1 1/4" (32 mm) x 15' (4,6 m) Inner Core Cable	3 1/2	1.60
62275	C-10	7/8" (22 m) x 15' (4,6 m) All- Purpose Wind Requires A-368-X Jawset	9 1/2	4.30
62280	C-11	1 1/4" (32 mm) x 15' (4,6 m) Standard All-Purpose Wind. 3⁄8" (10 mm) Pitch. Good for 4" (110 mm) Traps, 3" (75 mm) - 8" (200 mm) Lines	16	7.30
62285	C-12	15' (4,6 m) Extra-Heavy- Duty Wind. 3/8" (10 mm) Pitch. Recommended For 4" (110 mm) - 10" (250 mm) Long Runs, No 4" (110 mm) Traps	19	8.60
62295	C-14	15' (4,6) Heavy-Duty Wind. 1/2" (13 mm) Pitch. Recommended For 3" (75 mm) - 10" (250 mm) Lines Through Cleanout, No 4" (110 mm) Traps	16	6.80
62300	C-15	15' (4,6) Extra-Flexible Wind. 1⁄2" (13 mm) Pitch. Recommended For 3" (75 mm) - 6" (150 mm) Lines Good for Traps	12	5.50
63090	T-27	1 1⁄4" (32 mm) x 25" (63,5 cm) Leader	2 3/4	1.20

Accessories

Catalog Number	Model No.	Description	Weight
Catalog Number	Model No.	Description	lb.	kg
59205	A-1	Left-Hand RIDGID Drain Cleaning Mitt	1/2	0.20
59225	A-12	1/2" Cable Pin Key	1/2	0.20
59240	A-17	Manhole Guide Pipe	23	10.40
59295	A-2	Right-Hand RIDGID Drain Cleaning Mitt	1/2	0.20
59300	A-20	8-Foot (2,4 m) Front Guide Hose Assembly	25	11.40
59320	A-369X	Jaw Assembly 1-1/4" Cable	3/4	0.30
59360	A-3	Tool Box	5	2.30
59395	A-34-12	12-Foot (3,7 m) Rear Guide Hose	20	9.10
59415	A-34-10	10-Foot (3,1 m) Rear Guide Hose	13 3/8	6.20
59440	A-4	Trap Spoon (30", 76 cm)	1 3/4	0.80
59470	A-8	Cable Carrier 60' (18 m) Capacity 1 1/4" (32 mm)	5 1/2	2.50
59475	A-9	Cable Carrier 150-Foot (45,7) Capacity 11⁄4" (32 mm)	14	6.40
59400	A-34-16	16-Foot (4,9 m) Rear Guide Hose	26 1/2	12.00

Reviews
Q&A

K-1500G Sectional Machine is rated 5.0 out of 5 by 1.

Rated 5 out of 5 by rosco from this prodduct has always done the job this is a great machine for unclogging 3or 4 inch sewer pipe we have a resort people are always putting diapers or other stuff that clogs the pipes this machine has always fixed the problem even gets tree roots out works great

Date published: 2014-11-24