- The Model 1224 threads a wide range of pipe including black, galvanized and plastic-coated pipe, together with stainless steel, IMC and heavy-wall conduit, as well as rod up to 30 Rockwell C.
- An induction motor helps minimize noise.
- A special capacitor-start / capacitor-run motor allows the 1224 to thread a full range of material where voltage drop is experienced.
- 1/4"-2" Universal Die Head; 2 1/2"-4" receding die head allows cutting of tapered or straight NPT/NPSM or BSPT/BSPP threads.
- Constant and proper lubrication of dies and workpiece with through-head oiling.
|Nominal Pipe Capacity||1/4"-2" (6mm-100mm) @ 36 RPM, 2-1/2"-4" (65mm-100mm) @ 12 RPM, 4"-6" (100mm-150mm) with 161 Geared Threader.|
|Bolt Capacity||1/4"-2" (6mm-50mm).|
|Motor Control||Reverse/off/forward, heavy-duty rotary-type and integral foot switch.|
|Gear Box||Two-speed gear box with a 3:1 ratio.|
|Chuck||Hammer-type with replaceable rocker-action jaw inserts.|
|Rear Centering Device||Cam action.|
|Oiling Pump||Self-priming, gerotor-type, automatic-reversing, constant-flow.|
|Oiling||Through die head|
|Catalog Number||Model No.||Description||Die Head||RPM||Voltage (V)||Frequency (Hz)||Phase||Motor Type||Amp Draw (A)||Power||Weight|
|26092||1224||1/2" - 4" NPT Hammer Chuck Machine||711/714||36/12||120||60||1||Induction||15||1 1/2 HP||509.0||231.0|
|26097||1224||1/2" - 4" NPT Hammer Chuck Machine||711/714||36/12||230||60||1||Induction||8||1 1/2 HP||509.0||231.0|
|26127||1224||1/2" - 4" BSPT Hammer Chuck Machine||911/914||36/12||120||60||1||Induction||15||1 1/2 HP||509.0||231.0|
|26112||1224||1/2" - 4" BSPT Hammer Chuck Machine||911/914||36/12||115||50||1||Induction||15||1700 W||463.0||210.0|
|26122||1224||1/2" - 4" BSPT Hammer Chuck Machine||911/914||36/12||230||60||1||Induction||8||1700 W||509.0||231.0|
|26107||1224||1/2" - 4" BSPT Hammer Chuck Machine||911/914||36/12||230||50||1||Induction||8||1700 W||463.0||210.0|
|31442||1224||1/2" - 4" NPT Hammer Chuck Machine||711/714||36/12||230||50||1||Induction||8||1700 W||463.0||210.0|
Note: Die Heads do not include dies. All Die Heads are through-head oiling
|Catalog Number||Model No.||Description||Capacity||Weight|
|51005||819||819 Nipple Chuck Complete, 1/2" - 2" NPT||0.5 - 2.0||6.0 - 50.0||10.5||4.8|
|61122||840A||840A Universal Drive Shaft||-||-||31.0||14.1|
|26187||Jaw Insert and Roll Set for PE-Coated Pipe||-||-||0.2||0.1|
|26212||764||1/4"-4" Wheel-Type Cutter||-||-||19.0||8.6|
|26217||744||1/4"-4" Blade-Type Reamer||-||-||13.0||5.9|
|26707||Transmission Grease, 1 Lb.||-||-||1.0||0.5|
|34157||419||Nipple Chuck 2 1/2" NPT||-||-||5.5||2.5|
|34162||419||Nipple Chuck 3" NPT||-||-||5.5||2.5|
|34167||419||Nipple Chuck 4" NPT||-||-||5.5||2.5|
|34172||419||Nipple Chuck 21/2" BSPT||-||-||5.5||2.5|
|34177||419||Nipple Chuck 3" BSPT||-||-||5.5||2.5|
|34182||419||Nipple Chuck 4" BSPT||-||-||5.5||2.5|
|34577||Reamer Blade 1/4" - 4"||-||-||0.5||0.2|
Is there a stationary non-adjustable pipe die set for this pipe machine
Reason - the adjustable dies are sometimes out of calibration - our mechanics want a non-adjustable EX. .5" npt , .75" npt, 1" npt, etc.
We never ran into this situation so I can't answer with a simple yes/no. What we do is after noticing a little wear on the dies which is normal, is set, thread a sample check thread insertion in a fitting, then set and forget. One thing we have run across in my time is a lot of different suppliers outsource the fittings and although they meet specs there is a generally accepted tolerance of thread depth/insertion. We have found you can find a common neutral point between the fittings in hand we can set the thread depth/insertion to and it's not an issue then.
Date published: 2015-01-24
I have had issues with the oil overflowing and I assume too much was put in. Is there a set amount to have in at all times or some reference point to add to?
I filled (1 Gal) my oil reservoir until i could see the level just below the small secondary screen and I had no problem with overflows. Also getting the angle of the machine correct was critical in keeping the oil in the machine. Initially our machine was level and the oil would run out of the back of the pipe but bumping the rear legs up a bit fixed that..
Date published: 2015-10-13
Can the Model 1224 put an NPT thread onto 4'' SCH pipe grade 316
Thanks for contacting RIDGID. This machine is able to do this thread, but you will need the stainless steel dies to accomplish it. The part number would be 33057 for the dies for 4" Stainless Steel pipe. Please let us know if you have any other questions.
Date published: 2016-04-12